EN
Sign In Get Started
Get Started Sign In

Loncin ECU
Flashing

Flash the Bosch ECU in your Loncin XWolf 550L or 700L ATV through the diagnostic connector.

2Models
2Model years
2ECU families
Find your Loncin See pricing
Supported models

Every Loncin we can flash

Model years, the ECU inside and the interface it needs. Bench wiring diagrams for every model are in your MotoFlasher account.

Model Years ECU Interface
XWOLF 550L 2024–2025 Bosch MSE8.0 1.5 MB Tactrix OpenPort 2.0CANable
XWOLF 700L 2025–2025 Bosch MSE6.0 1.5 MB Tactrix OpenPort 2.0CANable
Inside the bike

Loncin ECU families

Which engine computer each model uses decides how it is read and written. MotoFlasher picks the right protocol for you.

Bosch Included

MSE8.0

1.5 MB

XWOLF 550L

Tactrix OpenPort 2.0CANable
Bosch Included

MSE6.0

1.5 MB

XWOLF 700L

Tactrix OpenPort 2.0CANable
How it works

Flash your Loncin in four steps

  1. 01

    Connect

    Plug your interface into the diagnostic port, or wire the ECU on the bench with the diagram from your account.

  2. 02

    Read & back up

    MotoFlasher identifies the ECU and reads the full flash. Keep that original file: it is your way back.

  3. 03

    Tune

    Edit fuel, ignition, limiters and the other maps in your tuning editor, or load a file from your tuner.

  4. 04

    Write

    MotoFlasher corrects the checksum and writes the file back. Start the bike and ride.

Why flash a Loncin XWolf?

The XWolf quads run Bosch engine management with a calibration written for emission tests: lean at small throttle openings and soft at low speed. A reflash smooths the throttle for technical riding, corrects the fuelling for an exhaust or intake change and lets you set the limits.

Loncin ECU families

  • Bosch MSE8.0: the XWolf 550L (2024 onwards).
  • Bosch MSE6.0: the XWolf 700L (2025).

Both are read and written through the diagnostic connector with a Tactrix OpenPort 2.0 or CANable.

Flashing a Loncin XWolf, step by step

  1. Keep the battery on a charger.
  2. Connect a Tactrix OpenPort 2.0 or CANable to the diagnostic connector.
  3. Read the ECU and save the original file.
  4. Edit the maps or load the file from your tuner.
  5. Write it back. MotoFlasher corrects the checksum.

Frequently asked questions

Is the Loncin XWolf 700L supported?

Yes, on the Bosch MSE6.0 ECU.

Which interface do I need?

A Tactrix OpenPort 2.0 or a CANable.

Can I go back to the stock map?

Yes. MotoFlasher reads the full original file before writing anything, and you can write it back at any time.

More brands

Flashing another brand?

Aprilia 12 models Benelli 6 models BMW 3 models CFMoto 47 models Ducati 12 models GOES 7 models Honda 19 models Italjet 1 model Kawasaki 33 models Kove 13 models KTM 7 models Moto Guzzi 5 models Moto Morini 3 models ODES 1 model Piaggio 4 models QJ Motor 9 models Segway 5 models Suzuki 17 models Triumph 14 models Voge 20 models Yamaha 17 models Zontes 17 models ZX Moto 1 model

Ready to flash your Loncin?

One license, every supported model of the brand, free software updates and support from people who tune bikes.

Get Started Ask a question