EN
Sign In Get Started
Get Started Sign In

Moto Morini ECU
Flashing

Flash the Bosch MSE6.0 ECU in your Moto Morini X-Cape 650, X-Cape 700 or Seiemmezzo through the diagnostic connector.

3Models
3Model years
1ECU families
Find your Moto Morini See pricing
Supported models

Every Moto Morini we can flash

Model years, the ECU inside and the interface it needs. Bench wiring diagrams for every model are in your MotoFlasher account.

Model Years ECU Interface
SEIEMMEZZO STR 2022–2025 Bosch MSE6.0 1.5 MB Tactrix OpenPort 2.0CANable
X-CAPE 650 2021–2025 Bosch MSE6.0 1.5 MB Tactrix OpenPort 2.0CANable
X-CAPE 700 2025–2025 Bosch MSE6.0 1.5 MB Tactrix OpenPort 2.0CANable
Inside the bike

Moto Morini ECU families

Which engine computer each model uses decides how it is read and written. MotoFlasher picks the right protocol for you.

Bosch Included

MSE6.0

1.5 MB

SEIEMMEZZO STR, X-CAPE 650, X-CAPE 700

Tactrix OpenPort 2.0CANable
How it works

Flash your Moto Morini in four steps

  1. 01

    Connect

    Plug your interface into the diagnostic port, or wire the ECU on the bench with the diagram from your account.

  2. 02

    Read & back up

    MotoFlasher identifies the ECU and reads the full flash. Keep that original file: it is your way back.

  3. 03

    Tune

    Edit fuel, ignition, limiters and the other maps in your tuning editor, or load a file from your tuner.

  4. 04

    Write

    MotoFlasher corrects the checksum and writes the file back. Start the bike and ride.

Why flash a Moto Morini ECU?

The X-Cape and Seiemmezzo share a parallel twin with a conservative Bosch calibration: lean fuelling at small throttle openings, a soft response and limits written for emission tests. A reflash smooths the pick-up, matches the fuelling to an exhaust and sets the bike up for how you ride, on the road or off it.

Moto Morini ECU

All supported models use the Bosch MSE6.0 ECU: the X-Cape 650 (2021 onwards), the X-Cape 700 (2025) and the Seiemmezzo STR (2022 onwards). It is read and written through the diagnostic connector with a Tactrix OpenPort 2.0 or CANable.

Flashing a Moto Morini, step by step

  1. Keep the battery on a charger.
  2. Connect a Tactrix OpenPort 2.0 or CANable to the diagnostic connector.
  3. Read the ECU and save the original file.
  4. Edit the maps or load the file from your tuner.
  5. Write it back. MotoFlasher corrects the checksum.

Frequently asked questions

Is the Moto Morini X-Cape 650 supported?

Yes, from 2021, on the Bosch MSE6.0 ECU.

Which interface do I need?

A Tactrix OpenPort 2.0 or a CANable.

Can I go back to the stock map?

Yes. MotoFlasher reads the full original file before writing anything, and you can write it back at any time.

More brands

Flashing another brand?

Aprilia 12 models Benelli 6 models BMW 3 models CFMoto 47 models Ducati 12 models GOES 7 models Honda 19 models Italjet 1 model Kawasaki 33 models Kove 13 models KTM 7 models Loncin 2 models Moto Guzzi 5 models ODES 1 model Piaggio 4 models QJ Motor 9 models Segway 5 models Suzuki 17 models Triumph 14 models Voge 20 models Yamaha 17 models Zontes 17 models ZX Moto 1 model

Ready to flash your Moto Morini?

One license, every supported model of the brand, free software updates and support from people who tune bikes.

Get Started Ask a question