EN
Sign In Get Started
Get Started Sign In

Segway ECU
Flashing

Flash the Bosch ECU in your Segway Snarler, AT5, UT6, Fugleman UT10 or Villain SX10: MSE6.0, MSE8.0 and MED17 units through the diagnostic connector.

5Models
5Model years
3ECU families
Find your Segway See pricing
Supported models

Every Segway we can flash

Model years, the ECU inside and the interface it needs. Bench wiring diagrams for every model are in your MotoFlasher account.

Model Years ECU Interface
AT5 S 2024–2029 Bosch MSE8.0 1.5 MB Tactrix OpenPort 2.0CANable
UT6 2024–2025 Bosch MSE8.0 1.5 MB Tactrix OpenPort 2.0CANable
SNARLER 2021–2025 Bosch MSE6.0 1.5 MB Tactrix OpenPort 2.0CANable
Villain SX10 X 2024+ Bosch MED17 CAN Boot+UDS · 1.5 MB Tactrix OpenPort 2.0CANable
Fugleman UT10 E 2022+ Bosch MED17 CAN Boot+UDS · 1.5 MB Tactrix OpenPort 2.0CANable
Inside the bike

Segway ECU families

Which engine computer each model uses decides how it is read and written. MotoFlasher picks the right protocol for you.

Bosch Included

MSE8.0

1.5 MB

AT5 S, UT6

Tactrix OpenPort 2.0CANable
Bosch Included

MED17

CAN Boot+UDS · 1.5 MB

Villain SX10 X, Fugleman UT10 E

Tactrix OpenPort 2.0CANable
Bosch Included

MSE6.0

1.5 MB

SNARLER

Tactrix OpenPort 2.0CANable
How it works

Flash your Segway in four steps

  1. 01

    Connect

    Plug your interface into the diagnostic port, or wire the ECU on the bench with the diagram from your account.

  2. 02

    Read & back up

    MotoFlasher identifies the ECU and reads the full flash. Keep that original file: it is your way back.

  3. 03

    Tune

    Edit fuel, ignition, limiters and the other maps in your tuning editor, or load a file from your tuner.

  4. 04

    Write

    MotoFlasher corrects the checksum and writes the file back. Start the bike and ride.

Why flash a Segway ATV or UTV?

Segway’s quads and side-by-sides run Bosch engine management with factory calibrations written for emission tests and the strictest road-legal markets. That means lean fuelling at small throttle openings, a soft response, and speed and power limits that make little sense off-road. A reflash lets you set the machine up for your terrain and your use.

Segway ECU families

  • Bosch MSE6.0: the Snarler ATV (2021 onwards).
  • Bosch MSE8.0: the AT5 S and UT6 (2024 onwards).
  • Bosch MED17: the Fugleman UT10 E (2022 onwards) and Villain SX10 X (2024 onwards).

All are read and written through the diagnostic connector with a Tactrix OpenPort 2.0 or CANable.

Flashing a Segway, step by step

  1. Keep the battery on a charger.
  2. Connect a Tactrix OpenPort 2.0 or CANable to the diagnostic connector.
  3. Read the ECU and save the original file.
  4. Edit the maps or load the file from your tuner.
  5. Write it back. MotoFlasher corrects the checksum.

Frequently asked questions

Is the Segway Villain SX10 supported?

Yes, the SX10 X from 2024, on the Bosch MED17 ECU.

Is the Segway Snarler supported?

Yes, from 2021, on the Bosch MSE6.0 ECU.

Which interface do I need?

A Tactrix OpenPort 2.0 or a CANable.

Can I go back to the stock map?

Yes. MotoFlasher reads the full original file before writing anything, and you can write it back at any time.

More brands

Flashing another brand?

Aprilia 12 models Benelli 6 models BMW 3 models CFMoto 47 models Ducati 12 models GOES 7 models Honda 19 models Italjet 1 model Kawasaki 33 models Kove 13 models KTM 7 models Loncin 2 models Moto Guzzi 5 models Moto Morini 3 models ODES 1 model Piaggio 4 models QJ Motor 9 models Suzuki 17 models Triumph 14 models Voge 20 models Yamaha 17 models Zontes 17 models ZX Moto 1 model

Ready to flash your Segway?

One license, every supported model of the brand, free software updates and support from people who tune bikes.

Get Started Ask a question